Right Angle Design
Right Angle Stitch

A Sewing Legacy

Old-school technique. New-school expression.

Free preview · Lesson 1 of 2

Cuffs on Shirts

Virgil’s Worktable Series: ten original Right Angle Stitch written cuff steps, from interfacing to sleeve attachment and topstitching. Free preview available; studio filming in progress.

Virgil’s Worktable Series · Free preview available

Cuffs on shirts

Original Right Angle Stitch written teaching is available now. Filming in progress. Verified lesson coming soon.

Open the written previewJoin release list

Tools & materials

  • Shirt cuff pattern, two cuffs and two facings
  • Crisp interfacing suitable for the fabric
  • Prepared shirt sleeves: plackets, pleats or gathers, and underarm seams finished
  • Sewing machine, thread, pins and basting needle
  • Iron, pressing surface, scissors and a blunt point turner

Before you sew

Plan a right cuff and a left cuff. Finish the sleeve plackets, shape the sleeve bottoms with pleats or gathers, and sew the underarm seams before attaching either cuff.

Follow your garment pattern's marked seam lines and interfacing directions. Test stitches and pressing temperature on a scrap. Keep fingers clear of the needle, unplug before changing needles, and handle the iron on a stable heat-safe surface. Children need adult supervision.

The lesson, step by step

  1. 01

    Cut & mark the interfacing

    Use the cuff pattern to cut the two cuffs, two facings, and their interfacing. Choose enough interfacing body for a crisp cuff and mark the buttonhole positions on it. Identify the right and left cuff before sewing.

  2. 02

    Apply the interfacing

    At pointed corners, cut the interfacing diagonally just inside the seam line. For a fused layer, trim ½ in. (1.2 cm) around the edges and fuse to the cuff's wrong side following the product directions. For a basted layer, use long stitches ½ in. (1.2 cm) inside the edges, then trim the interfacing close to that stitching.

  3. 03

    Transfer buttonhole marks

    Carry the buttonhole marks to the cuff's right side with basting stitches so the positions remain visible during construction. Sew the buttonholes only after the cuff is finished.

  4. 04

    Press the notched cuff edge

    Fold the cuff's notched edge to the wrong side along its seam line and press. Trim this folded allowance to ¼ in. (6 mm) to reduce bulk in the final seam.

  5. 05

    Join cuff & facing

    With right sides together, sew the facing to the cuff along the edges without notches. Leave the notched attachment edge open and keep the pressed cuff edge free.

  6. 06

    Reinforce points & sew curves

    For corners, shorten to 18 stitches per inch (2.5 cm) for 1 in. (2.5 cm) on each side of the point. Take 1–2 tiny diagonal stitches across the tip to ease turning. On curved cuffs, sew slowly with a short reinforcement stitch.

  7. 07

    Grade, trim & notch

    Grade the seam to ¼ in. (6 mm) on the cuff layer and ⅛ in. (3 mm) on the facing. Trim diagonally across corners and taper both sides of each corner. Notch curves only as needed for a smooth turn, staying clear of the stitching.

  8. 08

    Turn & press

    Turn the cuff right side out. Gently shape the corners with a blunt point turner without piercing the fabric, then press. Check that the curves are smooth and the pressed notched edge is still ready to cover the attachment seam.

  9. 09

    Attach facing to sleeve

    First check: sleeve placket finished; sleeve bottom pleated or gathered; underarm seam sewn. Place the facing's right side against the sleeve's wrong side, matching notches and the facing mark to the underarm seam. Keep the placket and cuff ends level; ease the sleeve to fit, baste, then sew. Trim the cuff seam allowance to ⅛ in. (3 mm) and the sleeve allowance to ⅜ in. (9 mm). Press the seam toward the cuff.

  10. 10

    Edgestitch & topstitch

    On the outside, pin the folded cuff edge over the attachment seam and edgestitch that fold. Topstitch ¼ in. (6 mm) from every cuff edge, moving slowly on curves and pivoting at corners. Work the marked buttonholes once the cuff is completed.

From Virgil's Worktable Series · Cuffs on Shirts — original Right Angle Stitch written teaching from the family studio.

Mark complete

Finish all 10 written steps on your own project before marking the lesson complete.

Notes and completion are personal learning records, not physical pattern approval.

Next free lesson

Collar on a Self-Band

Virgil’s Worktable Series: seven original Right Angle Stitch written self-band collar steps, with plaid preparation and neck attachment. Free preview available; studio filming in progress.

Right Angle Stitch is independent, original family-studio sewing instruction. Virgil’s Worktable Series carries the family’s teaching forward. Free written previews are available; course films are in production.