Right Angle Design
Right Angle Stitch

A Sewing Legacy

Old-school technique. New-school expression.

Free preview · Lesson 2 of 2

Collar on a Self-Band

Virgil’s Worktable Series: seven original Right Angle Stitch written self-band collar steps, with plaid preparation and neck attachment. Free preview available; studio filming in progress.

Virgil’s Worktable Series · Free preview available

Collar on a self-band

Original Right Angle Stitch written teaching is available now. Filming in progress. Verified lesson coming soon.

Open the written previewJoin release list

Tools & materials

  • Self-band collar pattern: collar and band in one piece
  • Plaid fabric for upper collar and undercollar
  • Suitable interfacing cut from the collar pattern
  • Prepared shirt neck edge with notches marked
  • Sewing machine, thread, pins, scissors, iron and pressing surface

Before you sew

Use a self-band pattern, not a separate collar and stand. Match the plaid deliberately when cutting. Check the marked neck notches and seam line before joining the collar to the shirt.

Follow your garment pattern's marked seam lines and interfacing directions. Test stitches and pressing temperature on a scrap. Keep fingers clear of the needle, unplug before changing needles, and handle the iron on a stable heat-safe surface. Children need adult supervision.

The lesson, step by step

  1. 01

    Interface the collar

    Cut the collar and its built-in band as a single shape, with interfacing for that shape. For fusible interfacing, remove ½ in. (1.2 cm) around its edges before applying it according to the product directions. For machine-basting, sew ½ in. (1.2 cm) inside the edges, then cut the interfacing back close to that stitching.

  2. 02

    Prepare the undercollar

    At the undercollar's notched edge, fold the ⅝ in. (1.5 cm) seam allowance to the wrong side and press. Reduce this folded allowance to ¼ in. (6 mm). Keep the fold intact for the outside finish later.

  3. 03

    Stitch upper & undercollar

    Place the upper and undercollar right sides together and pin the edges without notches. Sew those edges, slowing down around curves. For a pointed collar, use 18 stitches per inch (2.5 cm) for 1 in. (2.5 cm) on either side of the point, with 2 diagonal stitches across the tip. Follow the marked seam line; leave the prepared neck edge open.

  4. 04

    Trim, clip & grade

    Reduce bulky allowances by grading the layers. Clip at the front corners up to, but not through, the seam stitching. Remove small notches along the curved band ends so they can turn smoothly. Do not cut the seam itself.

  5. 05

    Turn & press

    Turn the collar right side out and gently shape the corners. Roll the seam slightly toward the underside and press the collar and built-in band flat. Check the points and curves before joining the collar to the shirt.

  6. 06

    Attach band to neck edge

    Pin the right side of the integral collar band to the wrong side of the shirt at the neck edge. Match every notch; clip the shirt's neck allowance where the curve needs release. Sew the neck seam, trim its allowances, and press them toward the band.

  7. 07

    Finish the outside

    From the shirt's outside, bring the prepared folded edge over the neck seam, pin it in place, and baste. Edgestitch the band's lower edge to secure the fold. Topstitch the collar ¼ in. (6 mm) from its edges, taking care around curves and points.

From Virgil's Worktable Series · Collar on a Self-Band — original Right Angle Stitch written teaching from the family studio.

Separate-band collars & removable stays
  1. A separate collar and stand is a different construction. Interface the undercollar and one stand piece independently; this is not interchangeable with a self-band pattern.
  2. For optional removable stays, reinforce the marked buttonhole on the undercollar, open it before applying interfacing, and stitch a stay pocket that allows removal for washing.
  3. Sew collar halves from the centre back toward each front. Reinforce pointed tips with short stitches, grade the upper-collar allowance to ⅛ in. (3 mm) and the undercollar to ¼ in. (6 mm), then turn, roll the seam underneath and press.
  4. Baste the interfaced stand to the collar with cut edges even. Stitch the single-notched edge of the stand facing on the seam line, press under, and trim to ¼ in. (6 mm). Sandwich the collar between the stand pieces, matching dots and notches; sew, trim and notch without catching the collar outside the dots. Turn and press before attaching to the shirt.
  5. The close edgestitch around all separate-band edges applies only to that method. It is not an eighth required self-band step.

Mark complete

Finish all 7 written steps on your own project before marking the lesson complete.

Notes and completion are personal learning records, not physical pattern approval.

At your worktable

Your free learning, ready to revisit

Revisit your saved projects and notes whenever you need them. The filmed apron workshop and paid courses are not open yet.

Right Angle Stitch is independent, original family-studio sewing instruction. Virgil’s Worktable Series carries the family’s teaching forward. Free written previews are available; course films are in production.